A large-surface self-cleaning long-life filter is used to collect the dust particles and deposit them in a tray whilst a downstream fine filter reduces the dust pollution to an absolute minimum.
Self-cleaning filter system
Large-surface dust collector tray for
easy cleaning
Adjustable suction power
Controlled by the milling machine
via 24 V control signal
Service indicator for filter change and maintenance cycles
Technical specifications:
Dimensions (w x h x d): 41 x 74 x 51 cm
Weight: 39 kg
Mains voltage: 230V / 120V
Filter: HEPA
Control signal: 24 V DC
incorporating into your lab. Take advantage of cyclone technology and enjoy the
benefits of a maintenance-free, low-noise system.
Cyclone technology keeps filter costs down
Low filter resistance gives maximum suction power
Brushless turbine technology makes this extraction unit maintenance free and extremely quiet
The new Zenotec cyclon allows your lab to enter a new era. The use of cyclone technology enables up to 95 % of the coarse particles to be separated in a preseparation stage. This protects your filters and makes it easy to dispose of the particles in dust bags. The unique new design of this powerful sound-insulated extraction unit means that it can easily be integrated into your lab. Take advantage of cyclone technology today and start to enjoy the benefits of this low-noise, zero-maintenance air extraction system.
Key features in brief
Low-noise
Easy to dispose of coarse particles by simply emptying the dust tray
Preseparator holds 15 liters
Large pre-filter for collecting medium-sized particles in the unit
HEPA filter (H13) for fine particles
Modular concept makes it easy to change filters
Brushless turbines (zero maintenance)
Infinitely adjustable power setting
Under-table unit
Electronic interface (start/stop, “filter-full” indicator)
Key features in brief
Five-axis simultaneous milling
Automated system with integrated 8-disc material changer*
Synchronous spindle with a maximum speed of 60,000 rpm and four hybrid ball bearings
16-position tool changer with automatic tool measurement and replacement tool management system
Absolute precisio:
repeatability value of ± 0,003 mm
Inclination angle of the rotation axes ± 180° (A-axis) and ± 30° (B-axis)
Wet operation*
Benchtop model with very small footprint
Further information
Technical specifications
Automation
Materials
Dry operation
Zirconia
Acrylic materials
Waxes
Wet operation*
Glass ceramics
Acrylic materials
Composites
Overview of features
Low-cost professional start-up
4-axis geometry
Automatic tool change and measurement
All indications – including fully contoured restorations
Including CAM software
Further information
Technical specifications
Automation
Materials
Software
In addition to the machine control system, the Zenotec mini software package also includes the Zenotec CAM basic software.
This is a valuable aid to blank management, ensuring the most space-saving nesting with a minimum of computation time. The performance of the Zenotec CAM basic system is enhanced by proven Wieland milling strategies and milling geometries. Your guarantee of the very best milling results.
Properties, Indications and more
Scanner specifications
S 50 'Zenostar'
Software package sold with scanner B
Scan speed – single die 50 (55) seconds
Scan speed – 3 unit bridge 180 (190) seconds
Multi Die Scanning
Number of axes 3
PC embedded
Operating system WINDOWS 7 64bit
Antagonist, Pre-preparation
Texture scanning
Cameras 1 measuring-, 1 video camera
1.3 Megapixels
Accuracy < 20 μm
Impression scanning
Modell Builder for impression and intraoral scans AddOn
Properties, Indications and more
Scanner specifications
Zenotec S50 CAD
Software package sold with scanner C
Scan speed – single die 50 (55) seconds
Scan speed – 3 unit bridge 180 (190) seconds
Multi Die Scanning - 6
Number of axes 3
PC embedded
Operating system WINDOWS 7 64bit
Antagonist, Pre-preparation
Texture scanning
Cameras 1 measuring , 1 video camera
1.3 Megapixels
Accuracy < 20 μm
Properties, Indications and more
Scanner specifications
S 50 'Implant'
Software package sold with scanner D
Scan speed – single die 50 (55) seconds
Scan speed – 3 unit bridge 180 (190) seconds
Multi Die Scanning - 6
Number of axes 3
PC embedded
Operating system WINDOWS 7 64bit
Antagonist, Pre-preparation
Texture scanning
Cameras 1 measuring, 1 video camera
1.3 Megapixels
Accuracy < 20 μm
Impression scanning
Modell Builder for impression and intraoral scans AddOn
Indications
Advanced tools
License
Properties, Indications and more
Scanner specifications
S107
Software package sold with scanner D
Scan speed – single die 35 (40) seconds
Scan speed – 3 unit bridge 120 (130) seconds
Multi Die Scanning - 30
Number of axes 5
PC embedded
Operating system WINDOWS 7 64bit
Antagonist, Pre-preparation
Texture scanning
Cameras 2 measuring , 1 video camera
1.3 Megapixels
Accuracy < 20 µm
Impression scanning
Modell Builder for impression and intraoral scans
Indications
Advanced tools
License
Wieland ZENOTEC T1
Commissioned by Wieland Dental & Technik, we developed the Zenotec T1, a fully automated 5-axis dental milling machine with optional tool changing.
At the heart of the machine are the entirely new milling kinematics and strategy, developed from the ground up especially for the requirements of dental technology. The technical features including the optimized milling tools, as well as the design of the complete unit are our own developments. The unit was realized with Wieland and specialized partners under our technical project management.
Zenotec Fire P1 fast sintering program:
! Only suitable for Zenostar T/MO single-tooth restorations !
Temperature 1 [°C] / [°F] Temperature 2 [°C] / [°F] Heating rate [°C/h] / [°F/h] Holding time [h]
Heating phase 20 / 68 1520 / 2768 1500 / 2732 -
Holding phase 1520 / 2768 1520 / 2768 - 0.5
Cooling phase 1520 / 2768 300 / 572 800 / 1472 -
For the sintering process in the Zenotec high-temperature furnaces, the following points should be observed:
If a standard program is used, it is recommended to sinter the restorations on a sintering support base plate under a highpurity
Al2O3 cover. This arrangement helps prevent deformation and discoloration from occurring in the restoration. All
standard sintering programs are matched to this configuration.
If a fast sintering program is used, only the sintering support base plate - without the cover - must be used. Fast sintering
is only suitable for ZenostarT/MO single-tooth restorations.
Check sintering auxiliaries regularly to make sure that they are clean and work properly
Characteristics
Function:
sintering
Applications:
for dental laboratories
Designed for:
ceramic
Other characteristics:
bench-top
Temperature range:
Min.: 0 °C (32 °F)
Max.: 1,500 °C (2,732 °F)
Sintering Zenotec Fire Cube
Standard program Zenostar MT/T/MO 1500°C/2h (2732°F/2h):
Temperature 1 [°C] / [°F] Temperature 2 [°C] / [°F] Heating rate [°C/h] / [°F/h] Holding time [h]
Heating phase 20 / 68 900 / 1652 600 / 1112 -
Holding phase 900 / 1652 900 / 1652 - 0.5
Heating phase 900 / 1652 1500 / 2732 200 / 392 -
Holding phase 1500 / 2732 1500 / 2732 - 2
Cooling phase 1500 / 2732 900 / 1652 600 / 1112 -
Cooling phase 900 / 1652 300 / 572 500 / 9
For the sintering process in the Zenotec high-temperature furnaces, the following points should be observed:
If a standard program is used, it is recommended to sinter the restorations on a sintering support base plate under a highpurity
Al2O3 cover. This arrangement helps prevent deformation and discoloration from occurring in the restoration. All
standard sintering programs are matched to this configuration.
If a fast sintering program is used, only the sintering support base plate - without the cover - must be used. Fast sintering
is only suitable for Zenostar T/MO single-tooth restorations.
Check sintering auxiliaries regularly to make sure that they are clean and work properly.
Wieland Zenotec select ion
Zenotec select ion has been developed with a view to optimizing the milling tools, systems, software programs, materials and machinery to allow for easy processing of acrylic materials - and achieve a coordinated digital manufacturing process. The machine is suited particularly for the digital production of complete dentures, bite templates, try-in mock-ups, positioning templates, bite splints and PMMA restorations
Innovative ionization system
When acrylic materials are processed, electrostatically charged particles are released. Ionized compressed air is directed onto the tools and materials via targeted nozzles during the processing operation to neutralize the electrostatic charge. The acrylic particles can be conveniently evacuated.
Key features in brief
Five-axis simultaneous milling
Automated system with integrated 8-disc material changer
Synchronous spindle with a maximum speed of 60,000 rpm and four hybrid ball bearings
16-position tool changer with automatic tool measurement and replacement tool management system
Absolute precision: repeatability value of ± 0,003 mm
Inclination angle of the rotation axes ± 180° (A-axis) and ± 30° (B-axis)
Property Value
Dimensions in cm (w x h x d) 49.0 x 54.0 x 44.5 (without changer)
69.2 x 54.0 x 44.5 (including changer)
Weight ca. 100 kg
Milling stations 1 (dry)
Spindle synchronous spindle with 4 hybrid ball bearings and integrated inner taper shank cleaning
max. output 600 W,
max. speed 60,000 rpm
Tool holder pneumatic chuck for tools with 3 mm shank
Tool positions 16; including replacement tool management system
Automatic tool measurement with breakage detection yes
Inclination angle of the rotation axes ± 180° (A-axis) and
± 30° (B-axis)
Repeatability value ± 0,003 mm
Material changer for 8 discs
Remote maintenance yes
Compressed air connection min. 7 bar
Voltage / frequency 230 V / 50 Hz
Benchtop model with very small footprint
Wieland Zenotec select hybrid
The new efficiency in dental technology
The Zenotec select hybrid combines a compact CNC milling system featuring state-of-the-art five-axis simultaneous operation with the advantages of automated manufacture and very compact external dimensions. Thanks to the 8-disc material changer, the machine can easily be set to work overnight and handling new materials presents no problem. By adding the optional wet-grinding function, the familiar range of materials can be extended to include materials such as glass ceramics and lithium disilicates.
Key features in brief
Five-axis simultaneous milling
Automated system with integrated 8-disc material changer
Synchronous spindle with a maximum speed of 60,000 rpm and four hybrid ball bearings
16-position tool changer with automatic tool measurement and replacement tool management system
Absolute precisio:
repeatability value of ± 0,003 mm
Inclination angle of the rotation axes ± 180° (A-axis) and ± 30° (B-axis)
Wet operation
Benchtop model with very small footprint
spectification:
Property Value
Dimensions in cm (w x h x d) 49.0 x 54.0 x 44.5 (without changer)
69.2 x 54.0 x 44.5 (including changer)
Weight 75 kg (without changer)
95 kg (with changer)
Milling stations 1 (dry/wet)
Spindle synchronous spindle with 4 hybrid ball bearings and integrated inner taper shank cleaning
max. output 600 W,
max. speed 60,000 rpm
Tool holder pneumatic chuck for tools with 3 mm shank
Tool positions 16; including replacement tool management system
Automatic tool measurement with breakage detection yes
Inclination angle of the rotation axes ± 180° (A-axis) and
± 30° (B-axis)
Repeatability value ± 0,003 mm
Material changer for 8 discs
Remote maintenance yes
Compressed air connection min. 7 bar
Voltage / frequency 230 V / 50 Hz
Wieland dental AGC Micro Vision
AGC Micro Vision - Conclusive application through a perfectly-tuned system
AGC Micro Vision is the leading fully-automated dental electroforming system. The safety, robustness and resistance of the electroforming units were and still are true pillars of WIELAND‘s market-leading position in electroforming technology. Using a selfexplanatory and menu-controlled touch panel with pre-stored electroforming programmes operating them is child‘s play. The processing steps are monitored and can be called up onto the display by the user at any time. Manual operation is simple and easy too. Placement and cleaning are also straight-forward.
This overview demonstrates why AGC Micro Vision is a market-leader:
Proven WIELAND AGC product quality in a complete design
Straightforward operation using a self-explanatory, menu-controlled touch screen
Reusable magnetic contacts with simple positioning
Unique, stain-resistant „Varicor“ housing, unique to the dental industry
Beaker with carry grip and clip for comfortable handling
Excess gold can be retrieved in the unit
